Skip to content Skip to sidebar Skip to footer
Home / How to Set Up My Momentum Camera Again

How to Set Up My Momentum Camera Again

Post a Comment

In this article, there are 5 means you tin connect your Security IP Camera to your figurer. And we will cover the steps on how yous should do it without a router, without net, without a DVR/NVR or without its receiver. The post-obit table summarizes the important information almost connecting IP photographic camera to your estimator for your reference.

Camera types: POE camera or WiFi camera
Bone(operation system): Windows or Mac
Cable: 2-in-ane or iii-in-1 cable attached from the photographic camera
Remotely access by: Camera'due south UID

Note: First you should install the security camera in the right place. Y'all can refer to How to Install Domicile Security Cameras Successfully.

5 Methods to Connect Your Security IP Camera to PC/Mac：

To arrive easier for you to find the right solution, you tin can click and jump directly to the section you want.

For instance, if your camera is a PoE camera, then y'all can choose pick 3 or 4.

  • i. Connect Directly to PC/Mac (without Cyberspace)
  • two. Connect via Router (with Internet)
  • 3. PoE (Wired) Camera without Injector/Switch
  • four. PoE (Wired) Camera with Injector/Switch
  • five. Connect a CCTV Camera Organization to PC/Mac

Important Annotation: The methods recommended below may Non apply for the battery-powered security cameras, which crave initial setup on your phones.

Connect a WiFi or PoE Camera Directly to PC/Mac (without Internet)

Here's how to connect your security IP photographic camera direct to a PC/Mac without an NVR or DVR, without a router network, without WiFi, and without any costs or complicated configurations.

you lot need to prepare the photographic camera's power adapter and a network cable.

i. Get your security photographic camera charged.

Utilize the ability adapter to get the camera plugged-in and charged. Unremarkably, when y'all purchase a WiFi IP camera, it comes with a power adapter. For a PoE camera, ask the supplier and buy 1 that's workable for the camera.

2. Use the network cablevision to connect to the photographic camera and the computer.

Commonly at that place would be a 2-in-1 or 3-in-1 cable attached from the photographic camera. Find the network connector from that cable and utilize the network cablevision to connect to it. And then connect the other stop of the network cable to the computer. If your computer has a network already, disable information technology – make sure your computer is offline. Connect IP Camera Directly to PC

3. Scan and find out the security camera's IP address on the computer.

At present the security camera is connecting to your reckoner basically and physically. But you lot still can't view the camera on the computer. What you need to practice now is to browse and find out the photographic camera'south IP address. There should be surveillance software from the same supplier with the camera. Have our exam every bit an instance. Nosotros have Reolink Client on the estimator. Launch it and it volition automatically scan all the cameras in the aforementioned local LAN and show the default IP address (every photographic camera has a default and unique IP address when information technology leaves the mill). Easy peasy! Camera IP Address

4. Change the computer's IP address to the same network prefix of the IP camera.

So in Stride three, yous go your security photographic camera'due south default IP address. In our test, the default IP address of the camera we employ is 192.168.177.100, and at present y'all need to modify your computer's IP address to 192.168.177.x, where x identifies the node/host and is the number betwixt two and 254. So permit's say the estimator'south IP address is 192.168.177.12.

IP address 101: An IP accost consists of two parts – ane belongs to the network accost and one belongs to the node accost. All nodes on a given network share the aforementioned network prefix but have a unique host number.

Now to change the computer'south IP address (nosotros take Windows 10 as an case):

one) Press the Windows + R keyboard shortcut to bring out the Run box.

ii) Enter "ncpa.cpl" and open the "Network Connections" window.

Computer Run Box

3) Right-click your computer' network adapter and select "Backdrop".

Network Adapter Properties

4) Select your reckoner's Internet Protocol Version and click "Properties".

Internet Protocol Properties

five) Select "Use the following IP address" and modify the IP accost into 192.168.177.12.

Change Computer IP Address

And washed. Now your IP camera is connecting directly and communicating with your PC, considering they are now in the aforementioned little LAN. You can watch your IP camera with Reolink Client on your computer.

Important: Since there is no router network, the IP camera would not transmit data or send alarms to your phone. Still, yous tin tape and save all the footage onto your estimator.

If you're gonna use your IP camera with the reckoner all the time like this (without router network), yous'd amend change the default condition of your IP camera's IP address to the static to keep it the same all the time, because each time you reboot the IP camera, its IP accost will be changed and yous will need to exercise all the steps above again. To go on the IP photographic camera'due south IP address the same all the time, head to "Device Settings" and "Network Full general" on the Client (Reolink Customer in our test), and choose "Static" for "Network Admission". And done. Static IP Address for Camera

Connect a Wireless/WiFi Camera to Computer via Router (with Net)

If y'all practice accept WiFi network and need to remotely run across the IP camera when you lot're not at that place, you can connect your wireless or WiFi photographic camera to computer wirelessly via your router. Please annotation that you need to accept, at to the lowest degree, a ability adapter for the camera, a network cable, and a router.

1. Go your WiFi security camera charged.

Use the power adapter to get the camera plugged-in and charged.

ii. Use the network cable to connect to the camera and the router.

A WiF camera needs to connect to the router with a network cable for initial setup, because the new camera itself wouldn't recognize and auto-selection upwards a network that it never uses. Just after the correct WiFi settings can y'all disconnect the cable from the camera and the router. And yeah again, normally at that place would be a 2-in-one or 3-in-1 cable attached from the WiFi camera. Find the network connector from that cable and use the network cablevision to connect to it. Then connect the other stop of the network cable to the router. Connect WiFi Camera to PC

3. Watch the IP camera on PC/Mac

On the estimator, launch the surveillance software to add the camera and scout live view straight. In our examination, we open Reolink Client. Since the computer and the camera are in the same network (using the same router network), Reolink Customer automatically searches and displays the camera directly. Click "Start" and yous can view the camera on PC. And y'all can gear up up the configurations for all the functions y'all want the photographic camera to take.

iv. Ready WiFi settings and remove the network cablevision.

Do recall to make the WiFi settings for the photographic camera. On the software, navigate to "Device Settings" and "Network". Choose the WiFi network and enter the countersign, and done. Cameras from the dissimilar brands would accept different WiFi settings. Delight refer to the guides you get from your supplier. Afterward that, remove the network cablevision, and so the security IP CCTV camera connects to the calculator wirelessly.

Important: If you need to see the IP camera from another calculator that is non in the same network, you need to input the camera'south UID into the software to remotely access the photographic camera.

Connect a PoE (Wired) IP Camera to Calculator without PoE Injector/Switch

Connecting a PoE wired IP camera to a computer via the router is like to that of a WiFi photographic camera, and even much easier – you don't need to use a ability adapter, set up up the WiFi and remove the network cable. And y'all need at least one network cable, and a router with PoE capability to complete the setup.

1. Utilise the network cable to connect to the camera and the router.

PoE (Power over Ethernet) means you can just use a single network cable for both video and power transmission. So just connect the photographic camera to the router via the network cablevision, and the camera volition become power supply and network access. Cloud Storage Please make sure your router has the PoE feature. If not, try the adjacent method.

2. Scout the IP camera on the computer.

On the computer, launch the surveillance software to add together the camera and watch live view direct. In our test, we open up Reolink Client. Since the computer and the camera are in the same network, Reolink Client automatically searches and displays the photographic camera directly. Click "Start" and you can view the photographic camera on PC. And you lot can prepare the configurations for all the functions you want the camera to take.

Of import: If you need to run across the IP photographic camera from some other computer that is not in the same network, you need to input the camera'south UID into the software to remotely access the photographic camera.

Connect a PoE (Wired) IP Photographic camera to Computer with PoE Injector/Switch

If your router does not back up PoE, yous need a PoE injector or PoE switch to assistance connect your IP camera to PC.In society to complete the setup you need at least a network cable, a router, and a  PoE injector or PoE switch. Since the steps on how to connect a PoE IP camera to PC via PoE Injector/switch are quite the same to that of connecting without a PoE Injector/switch, we'd similar to brand information technology more simpler to empathize here.

1.connect the security camera, router and PoE injector

Connect all the devices as the movie showed below, make sure your wireless IP camera is connected to a ability supply. PoE Camera Connecting to PC

2. Open Reolink Customer & add the camera directly

You can now open Reolink Customer on your computer, add the camera and watch live view directly. If you need to see the IP camera from another estimator that is not in the same network, you need to input the camera's UID into the software to remotely access the camera.

Important: Once yous connect the PoE IP camera to the PoE injector or switch which is connected to a router via Ethernet cables, you've successfully connected the camera to the network. For a wireless IP camera, yous demand to use a network cablevision to connect it to the router if y'all haven't set the WiFi network configuration. And so the wireless IP photographic camera is in the network. You can set the WiFi configuration after to make the wireless IP photographic camera connect wirelessly.

Connect a CCTV Camera System to PC/Mac (with or without Network)

If you are using a CCTV photographic camera organization, like the Reolink PoE kit RLK8-410B4, instead of single security camera, you lot may demand the post-obit tutorial. A CCTV camera arrangement often have their own proprietary networks, and tin can work with and without your router network.

1. How to connect a CCTV security camera system to a figurer without router network

  • Connect all the cameras to the NVR:When you receive the new IP photographic camera organisation yous bought, connect all the devices y'all got – connect the NVR to your figurer's monitor and the mouse, apply the power adapters to accuse the NVR and cameras, etc. For a WiFi arrangement, once the WiFi NVR and the WiFi cameras are charged, they connected to each other automatically and would beginning to communicate. For a PoE system, connect the PoE cameras to the NVR via the network cables provided.
  • Start watching the IP cameras:The startup and setup sorcerer will popular upwardly to guide you to lookout man your cameras and do other configurations.

At present you can see all the IP cameras on your monitor and starting time recording.

2. How to connect a CCTV security photographic camera system to a reckoner with router network

  • Do the stride 1 shown above again.
  • Connect the NVR to your router via the network cable provided.
  • Start watching the IP cameras.

The startup and setup magician will pop upwardly to guide you to watch your cameras and practise other configurations. If you demand to meet the IP cameras from another computer that is not in the same network, y'all need to input the NVR'due south UID into the software to remotely admission the cameras.

Inforgraphic:

The infographic beneath also covers our 5 methods to connect IP security photographic camera to PC/Mac . Hope this tin be helpful to you.

How to Connect Security Camera to PC

Tertiary-Political party Software to Connect IP Photographic camera to PC/Mac

Y'all can also opt for third-political party software to connect and set upward a security camera on the computer. Make sure the software can handle all the cameras on the network and support all the features for the cameras. Normally, the third-party software has several versions. And if y'all want to use full features of the camera, y'all demand to pay for a premium version. If your security IP camera is not working properly as expected or if you get any problems, yous tin can try the summit 10 solutions to fix IP cameras not working.

For whatsoever questions, please don't hesitate to leave it in your comment. I will reply as soon as possible.

olsenthelint.blogspot.com

Source: https://reolink.com/connect-security-ip-camera-to-pc/

Post a Comment for "How to Set Up My Momentum Camera Again"